Skip to main content
Sonoma Sub-Zero Repair logo mark Sonoma Sub-Zero RepairSub-Zero built-in refrigeration | Sonoma 95476

Cove Water and filters · 5 min read

Cove Dishwasher Filter Location: Where It Sits and How to Lift It Out

The Cove dishwasher filter sits in the tub sump under the lower spray arm. Release it with a 1/8 turn, and learn what the 30-cycle Clean filter reminder means.

Cove Water and filters โ€” Cove Dishwasher Filter Location: Where It Sits and How to Lift It Out

The Cove dishwasher filter sits in the sump at the bottom of the tub, directly beneath the lower spray arm, so the lower rack and spray arm come out first. To release the Cove filter, press it down lightly, turn it counterclockwise 1/8 turn and lift it straight up.

Cove prompts this job with a Clean filter message every 30 cycles. That Cove reminder counts cycles rather than measuring soil, so a busy Sonoma kitchen may need filter attention sooner.

Where exactly is the filter inside a Cove dishwasher?

Pull out the Cove lower rack and remove the lower spray arm from the tub floor. The filter assembly sits underneath, seated in the sump where wash water collects before the Cove pump recirculates or drains it.

A Cove dishwasher behind a custom wood panel, as in a restored home near the 1840s Mexican-era adobes around Sonoma Plaza, a National Historic Landmark, needs no panel removal; reaching the Cove filter happens inside the open tub.

How do you take the Cove filter out and put it back?

Step 1: Switch the Cove dishwasher off and let the tub cool if a cycle just ended.

Step 2: Press the Cove filter down lightly, rotate it counterclockwise 1/8 turn and lift it out.

Step 3: Rinse the Cove filter under warm running water with a soft brush; a wire brush can tear the fine mesh.

Step 4: Seat the Cove filter in the sump, press lightly and turn it clockwise until it locks without rocking, then refit the spray arm. An unlocked Cove filter lets debris slip toward the pump.

Why does the Clean filter message appear every 30 cycles?

Cove logs this reminder as code 30 01 14 for the sump filter, and the count runs on cycles alone, so it appears whether the filter is spotless or packed with seeds. If the Cove Clean Filter reminder stays on after a proper cleaning, switch the breaker off for 30 seconds and retest; a reminder that persists is a controls question for a technician.

What water hardness does to the Cove filter and tub

Hard water leaves mineral scale that binds with food film, so the Cove filter mesh clogs sooner and the tub turns chalky. Very soft water brings the opposite Cove problem: detergent that never fully rinses away.

Cove scales liquid, gel and powder detergent to hardness: fill the cup 1/3 for 0-3 gpg, 2/3 for 4-8 gpg and full for 9+ gpg. Overdosing a Cove in very soft water can cloud glassware.

On the Cove DW2451WS, test the supply with the supplied strip, then set Water Hardness in User Set Up by holding Options about 10 seconds; 0 is the default for 0-4 gpg, and 10 covers 25+ gpg.

When a Cove shows Descale Unit. Check manual., empty the racks, add 3 tbsp (44 ml) of citric acid or a dishwasher cleaner to the detergent dispenser and run Soak & Scrub.

Which symptoms point to a clogged Cove filter?

Standing water with Error 800115. Check manual. signals a Cove drain problem. Clean the Cove filter, then confirm the air gap and drain line are clear, the disposal knockout is out, and the hose is neither kinked nor over 4' (1.2 m) above the dishwasher floor. Water that still stands needs a technician.

Error 80 01 40 (MOT4) on a Cove DW2450 means the drain pump ran too long. Clean the Cove filter and interior, cut the breaker for 30 seconds and retest; a repeat needs a technician.

Gritty specks on clean Cove dishes mean a loaded filter is recirculating debris. Clean the Cove filter and clear blocked spray-arm holes under running water with a paper clip.

A sour Cove smell usually traces to food trapped in the sump or mold on the door gasket. Clean the Cove filter and spray gasket mold with 3% hydrogen peroxide.

When should a technician take over from the owner?

A Cove filter that is cracked, warped or no longer locks with the 1/8 turn should be replaced, not forced, and drain errors that survive cleaning and a 30-second breaker reset are technician work.

Cove's limited five-year parts warranty covers the electronic control board, diverter valve, pump and racks, with the owner paying other costs, including labor; the stainless steel tub and door liner carry a limited lifetime parts warranty.

FAQ

Questions & answers

Is the Cove filter a part you swap out on a schedule?

No, the Cove filter is cleanable, and the Clean filter reminder every 30 cycles is a cleaning prompt. Replace the Cove filter only if the mesh tears, the frame cracks or it will not lock.

How often should the rest of a Cove dishwasher be cleaned?

Cove's DW2451 guide suggests cleaning the interior about every three months and the spray arms every six months, plus the filter whenever the Clean filter reminder appears.

Do all-in-one pods load up a Cove filter faster?

They can, because Cove warns that pods may supply too much detergent for the Light, Quick and China/Crystal cycles. Cove rates powder detergent, which combines enzymes and bleach, as giving the best results. A quick call to Sonoma Sub-Zero Repair at (628) 209-6820 settles it.

Go deeper

More Sonoma guides

All guides →

After the proof

Rather leave it to a specialist?

Have the failing compartment, current temperatures, and model number ready, and you will get a real first opinion — not a sales pitch.

Where the filter sitsIn the sump at the bottom of the tub, under the lower spray arm
Release motionPress down lightly, turn counterclockwise 1/8 turn, lift straight up
Clean filter reminderEvery 30 cycles (code 30 01 14), counted by cycles, not soil
Owner check vs technicianClean the filter and drain path yourself; drain errors that survive a 30-second breaker reset are technician work
Who to callSonoma Sub-Zero Repair โ€” (628) 209-6820